{"id":810,"date":"2025-10-27T11:08:29","date_gmt":"2025-10-27T11:08:29","guid":{"rendered":"https:\/\/dsdevices.com\/?page_id=810"},"modified":"2025-10-27T11:08:29","modified_gmt":"2025-10-27T11:08:29","slug":"dsda1-firmware-reflash","status":"publish","type":"page","link":"https:\/\/dsdevices.com\/eu\/dsda1-firmware-reflash\/","title":{"rendered":"DSDA1 Firmware Reflash"},"content":{"rendered":"\n

If your device is not working properly, follow the instructions below to fully reflash your device using the USB-USB method. <\/p>\n\n\n\n

For routine upgrades of the DSDA1 firmware, please use the OTA zip file<\/a> method. <\/p>\n\n\n\n

You will need a wooden or plastic stick that will easily fit inside the AV port on the rear of the DSDA1. A matchstick, cocktail stick or toothpick is ideal. Do not use anything metal or anything conductive. <\/p>\n\n\n\n

You will need a USB mouse. <\/p>\n\n\n\n

You will need to download the USB Burning Tool, DSDA1 Android Firmware and DSDA1 SHA256 Firmware Hash linked below: <\/p>\n\n\n\n

Aml USB Burn Tool V3<\/a>Download<\/a><\/div>\n\n\n\n

<\/p>\n\n\n\n

DSDA1 Firmware and Hash currently unavailable.<\/p>\n\n\n\n

Once the image has been downloaded please check the image hash.<\/p>\n\n\n\n

The mains power adapter should be connected to a power source, but not plugged into the DSDA1. <\/p>\n\n\n\n

Install USB Burning Tool<\/strong> <\/p>\n\n\n\n

On your Windows 10\/11 computer, extract the USB Burning Tool zip file<\/p>\n\n\n\n

Run USB Burning Tool<\/strong> <\/p>\n\n\n\n

Once the USB Burning Tool has been extracted, change to the unzipped directory and run Aml_Burn_Tool.exe.<\/p>\n\n\n\n

Next from the top File menu, choose settings, load image. <\/p>\n\n\n

\n
\"\"<\/figure>\n<\/div>\n\n\n

<\/p>\n\n\n\n

Select the img file you downloaded earlier. <\/p>\n\n\n\n

After a short time, the import will complete and you\u2019ll see the firmware loaded at the bottom of the screen: <\/p>\n\n\n\n

<\/p>\n\n\n

\n
\"\"<\/figure>\n<\/div>\n\n\n

Next ensure that the Configuration section to the top right looks like this: <\/p>\n\n\n

\n
\"\"<\/figure>\n<\/div>\n\n\n

<\/p>\n\n\n\n

Ensure Erase flash mode is set to Normal Erase as shown above. Under no circumstances use any other mode.<\/strong> <\/p>\n\n\n\n

Connect DSDA1<\/strong><\/p>\n\n\n\n

Ensure that the DSDA1 is turned off and that the power adapter is disconnected from the power port on the rear of the DSDA1. <\/p>\n\n\n\n

Put your matchstick or similar into the AV port on the rear of the DSDA1 and press gently. You should feel a tactile \u201cclick\u201d as you depress the reset button. <\/p>\n\n\n\n

Keep the reset button pressed. <\/p>\n\n\n\n

Plug one end of the USB A-A cable into the rear-most USB port of the DSDA1 (nearest to the antenna) and the other into a spare USB port on your Windows 10\/11 computer. <\/p>\n\n\n\n

Connect the power adapter to the DSDA1 and release the reset button. <\/p>\n\n\n\n

You should see a new device appear in the USB Burning Tool. <\/p>\n\n\n

\n
\"\"<\/figure>\n<\/div>\n\n\n

<\/p>\n\n\n\n

If it doesn\u2019t appear, remove the power and USB cables, reconnect the USB and then try the process of pressing the reset button and connecting power again. <\/p>\n\n\n\n

Once you have the device connected, click on the Start button at the top right of the USB Burning Tool. Immediately the device will start to be upgraded. <\/p>\n\n\n

\n
\"\"<\/figure>\n<\/div>\n\n\n

Allow the process to complete. When it has completed, you\u2019ll see the following: <\/p>\n\n\n

\n
\"\"<\/figure>\n<\/div>\n\n\n

Allow 5-10 seconds for any transfers that are in progress to complete, and then remove the USB cable from the DSDA1. <\/p>\n\n\n\n

If you\u2019re doing multiple DSDA1s, you can connect the next one at this point and it will automatically upgrade as soon as it is connected. <\/p>\n\n\n\n

When you\u2019ve finished upgrading devices, ensure the USB and power cables are disconnected from the DSDA1 and then click the Stop button. <\/p>\n\n\n\n

<\/p>\n","protected":false},"excerpt":{"rendered":"

If your device is not working properly, follow the instructions below to fully reflash your device using the USB-USB method.  For routine upgrades of…<\/p>\n","protected":false},"author":524,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"page-templates\/fullwidth.php","meta":{"_monsterinsights_skip_tracking":false,"footnotes":""},"class_list":["post-810","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/dsdevices.com\/eu\/wp-json\/wp\/v2\/pages\/810","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/dsdevices.com\/eu\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/dsdevices.com\/eu\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/dsdevices.com\/eu\/wp-json\/wp\/v2\/users\/524"}],"replies":[{"embeddable":true,"href":"https:\/\/dsdevices.com\/eu\/wp-json\/wp\/v2\/comments?post=810"}],"version-history":[{"count":0,"href":"https:\/\/dsdevices.com\/eu\/wp-json\/wp\/v2\/pages\/810\/revisions"}],"wp:attachment":[{"href":"https:\/\/dsdevices.com\/eu\/wp-json\/wp\/v2\/media?parent=810"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}